ADAMS ACID INJECTOR 5-8 GPM 2.3mm QC KIT
$71.99
ADAMS ADJ ACID INJECTOR 5-8GPM 2.3mm 20%
|
Product Description
|
|
Additional information
| Weight | 3 lbs |
|---|
Related Products
GP FIXED INJECTOR 2.3mm HI-DRAW (100776)
FEATURES: Up to 20% injection draw rate. Can be affected by factors such as pressure, flow rate, length of discharge hose and chemical viscosity. Made in USA A cost effective solution to your chemical application needs. SPECIFICATIONS: Operating pressure: 4500 PSI maximum Flow range: 5-8 GPM 190F. maximum temperature 3/8″ MPT inlet and discharge 1/4″ hose barb chemical port$18.59
HI-DRAW 2.1 FIXED INJECTOR 3/8MPT X 3/8MPT
Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. The injection rate for this injector is set at the factory and not adjustable. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode. NOTE: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less SPECIFICATIONS: Maximum pressure: 3600 PSI Maximum temperature: 300F. 2.7 to 4.9 GPM flow rate$20.99
MVR410 2.1 ADJ INJECTOR 3/8FPT X 3/8 MPT
Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode. NOTE: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less. SPECIFICATIONS: 15% draw at 1000 PSI or less 8 GPM maximum 3600 PSI maximum 160 F maximum 3/8″ FPT inlet$22.19
ROBOKIM #0 INJECTOR QC KIT (PLUG INLET & SOCKET OUTLET)
Refer to the arrow on the injector body for proper flow direction. Install the injector in the system downstream of the regulator unloader which is downstream of the pump. These injectors will draw your chemical into the water stream at 125 PSI and 2.1 to 10.8 GPM, through your low pressure nozzle. Injector WILL NOT draw chemical above 250 PSI through your high pressure nozzle. The amount of chemical drawn in is controlled with the adjustment knob. Maximum pressure: 3200 PSI. Maximum temperature: 210 degrees F. Inlet port: 3/8″ MPT. Outlet port: 3/8″ MPT. Dimensions: 1.0″ x 2.7″ x3.1″. Weight: .6 lb. Repair Kit: (chemical) Barens order #1270. (acid) Barens #3846.$70.55
ROBOKIM #0 INJECTOR 2.1-2.9 GPM 2.0mm
Downstream injectors are installed after the pump. In order to function, the pressure must be lowered with the use of either a dual lance and soap nozzle, a variable nozzle, a dual nozzle holder, or an adjustable nozzle holder. Water enters the inlet of the injector and creates a venturi which drops the pressure and suctions the chemical from container. Chemical can be injected either in concentrated form or in diluted form. Chemical can be regulated by turning the dial on the injector or installing a metering device on the chemical line. The injector contains a check valve to prevent water from flowing into the chemical container while in high pressure mode. NOTE: Length of hose will determine ability of injector to work properly. It is recommended to keep hose length at 100 feet or less.$54.71
Reviews
There are no reviews yet.